Skip to main content

Add your first DNS records

Add the records required for your services to a primary zone before changing its delegation.

Before you begin

  1. Confirm that the primary zone exists in DigiCert®​​ DNS.

  2. Confirm that your assigned roles permit you to create and update records.

  3. Obtain the required addresses, hostnames, mail priorities, verification values, and certificate authority identifiers from your service providers.

  4. Go to DNS > Zones > Primary zones, open the zone, and select Records.

  5. Review existing records to avoid adding duplicates.

If the zone already contains records you may need to recover, create a snapshot before making changes. See DNS snapshots.

Prepare record names and TTLs

  1. Identify the name each record should use. For example, in the example.com zone, enter www for www.example.com.

  2. Use @ when the record belongs at the zone apex, such as example.com.

  3. Check the zone suffix displayed below Name to confirm the resulting name.

  4. Obtain the value required by the service provider.

  5. Review TTL, which controls how long resolvers may cache the record. Use the provider’s specified value when one is supplied.

Add only the record types your services require.

Add an A or AAAA record

  1. Select Add record.

  2. Choose A for an IPv4 address or AAAA for an IPv6 address.

  3. Enter the record’s Name.

  4. Review TTL.

  5. Enter the destination IP address supplied by your service provider.

  6. Review Configure reverse PTR, which is selected by default. Clear it if you are not configuring reverse DNS as part of this setup.

  7. Select Save and close, or Save and add another to continue adding records.

  8. Confirm that the record appears with the intended name and address.

If you need a PTR record, follow Reverse DNS to configure the reverse zone.

Add a CAA record

  1. Confirm which certificate authorities your services use, including automated certificate renewal.

  2. Select Add record.

  3. Choose CAA (Certificate Authority Authorization).

  4. Enter Name. Use @ to configure the policy at the zone apex.

  5. Review TTL.

  6. Under Authorization policies, select Issue in Tag.

  7. Select the intended certificate authority under Provider and review the populated Value. If the provider is not listed, select Custom and enter its supplied CAA value.

  8. Leave Flags at 0: Not critical, unless your policy requires otherwise.

  9. To authorize another certificate authority at the same name, select Add another and configure another Issue entry.

  10. Review the policy summary and select Save and close.

  11. Confirm that the saved policies authorize the intended providers.

For separate wildcard policies, S/MIME and Verified Mark Certificate authorization, incident reporting, and critical flags, see CAA records.

Add a CNAME record

  1. Select Add record.

  2. Choose CNAME.

  3. Enter the record's Name, such as www.

  4. Review TTL.

  5. Enter the canonical hostname supplied by your service provider in Target hostname.

  6. Select Save and close.

  7. Confirm that the record points to the intended canonical hostname.

Use a hostname as the target, without a URL scheme or path. For a target outside the current zone, include a trailing dot to prevent the zone name from being appended. For configuration requirements and conflicts, see CNAME records.

Add an MX record

  1. Obtain the mail server hostnames and priority values from your email provider.

  2. Select Add record.

  3. Choose MX.

  4. Enter the required Name, typically @ when configuring email for the zone apex.

  5. Review TTL.

  6. Enter the mail server hostname and its priority.

  7. Use Add another for additional mail server entries, supplying each hostname and priority as specified by the provider.

  8. Select Save and close.

  9. Compare the saved entries with the provider’s instructions.

For priority behavior and mail-server requirements, see MX records.

Add a TXT record

  1. Obtain the exact TXT name and value from the service provider.

  2. Select Add record.

  3. Choose TXT (Text).

  4. Enter Name and review TTL.

  5. Under Syntax, select the appropriate TXT record type: Generic, SPF, DKIM, DMARC, or BIMI.

  6. Paste the record value into Contains.

  7. Select Save and close. The form automatically validates the TXT record. If validation fails, correct the reported issue and save again.

  8. Confirm that the saved name and value match the provider’s instructions.

Enter the TXT value rather than a complete zone file record. Validation checks the supported syntax; it does not confirm that the external service has completed setup.

For type-specific requirements, see TXT records.

Review and correct the records

  1. On Records, use Grouped view or Table view to review the entries.

  2. Compare each name, type, value, and TTL with your service provider instructions.

  3. If a value is incorrect, open the record’s edit action.

  4. Update the required fields and select Update.

  5. If you created an unnecessary record, select its delete action, review the confirmation, and confirm deletion.

If saving reports that a record with the same name and type already exists, edit that record to add or update its values.

If the zone is not yet delegated to DigiCert®​​ DNS, public lookups may still return answers from the previous provider. Verify delegation and DNS responses in the next guide.

Next steps